Flushing, Safety Checks, Permits, and Storm Prep
Most people don’t think about their water heater until the shower runs cold or water spreads across the garage floor. A little routine care can prevent both. Sediment settles at the bottom of the tank, the anode rod that protects the tank from rust slowly wears away, and the safety valve that keeps the tank from over-pressurizing can stick if nobody ever tests it. In Florida, many water heaters sit in garages that get hot and can flood, and a full tank doubles as an emergency water supply during hurricane season. This guide covers a simple maintenance schedule, how to flush the tank and test the relief valve, the right temperature setting, gas safety, permits for replacement, storm prep, and the federal efficiency rules coming in 2029. It’s part five of our series on yard and home rules.
Short version: Drain a gallon or two from the tank every six months to clear sediment, and flush it fully once a year following your owner’s manual. Test the temperature and pressure relief valve once a year and replace it if it doesn’t work. Have the anode rod checked starting around year three to five. The Consumer Product Safety Commission recommends setting your water heater to 120°F, since 140°F water can burn in six seconds. Gas water heaters must vent outdoors, and Florida law requires carbon monoxide alarms near bedrooms in homes built since July 1, 2008 that have fuel-burning appliances or an attached garage. In unincorporated Orange County, replacing a water heater requires a plumbing permit and possibly an electrical permit. During an outage or boil-water notice, the water in your tank is safe to drink. New federal efficiency standards for tank water heaters apply to units made on or after May 6, 2029.
A simple maintenance schedule
| How often | Task | Why |
|---|---|---|
| Every 3 months | Look around the tank: leaks, rust, and any insulation blanket that has shifted | On gas units, a blanket must never block the air inlet or vent |
| Every 6 months | Drain 1 to 2 gallons from the drain valve | Clears loose sediment and keeps the drain valve working |
| Once a year | Full flush per the manufacturer’s steps; test the relief valve; inspect the gas vent | Sediment reduces heating and can burn out electric elements; the valve is a safety device |
| Year 3 to 5, then as needed | Check or replace the anode rod | The rod corrodes so the tank doesn’t |
| Any time | Keep the temperature at or below 120°F | Reduces scald risk, scale, and energy use |
Based on public works maintenance guidance from the Village of Carpentersville, Illinois, and the Consumer Product Safety Commission. Your owner’s manual takes priority for your specific model.
How to flush a tank water heater
- Turn off the power at the breaker for an electric unit, or set a gas unit to “pilot” or “off.”
- Let the water cool for a few hours, or be careful, since it can be scalding.
- Attach a garden hose to the drain valve and run it to a driveway, floor drain, or outside.
- Open a hot water faucet in the house so air can enter, then open the drain valve.
- Once it’s drained, briefly open the cold supply to stir up and rinse out remaining sediment, until the water runs clear.
- Close the drain valve, refill the tank, and wait until water flows steadily from the open hot faucet.
- Only then restore power or relight the gas. Turning on an electric heater with an empty tank can burn out the elements.
If the drain valve won’t reseal after years without use, its washer may need replacing. If you’re not comfortable with any step, a licensed plumber can do the yearly service.
Relief valve and anode rod
- Temperature and pressure relief valve: this valve opens if the tank gets too hot or the pressure gets too high. Test it once a year following your manual, usually by lifting the lever briefly with a bucket under the discharge pipe. If it doesn’t release water, or keeps dripping afterward, have it replaced. Never cap or plug the discharge pipe.
- Anode rod: a metal rod inside the tank that corrodes in place of the steel tank. Once it’s mostly gone, the tank starts to rust. Replacing a worn rod is much cheaper than replacing the heater. Water softeners can wear rods faster, so consider a check around year three to five.
- Hard water: if your water is hard, sediment and scale build up faster, so flush more often. Many utilities’ annual water quality reports list hardness.
The right temperature
The Consumer Product Safety Commission urges setting water heaters to 120°F. Water at 140°F can cause burns in six seconds, while at 120°F it takes about five minutes to cause third-degree burns. Young children and older adults are at the highest risk. To check the temperature, run hot water from a faucet first thing in the morning and hold a cooking thermometer under it. Electric units often have two thermostats, so turn off the power before adjusting and set both to the same temperature.
Gas water heaters and carbon monoxide
- Venting: fuel-burning water heaters must vent outdoors. Once a year, check that the vent pipe is connected, isn’t rusted through, and isn’t blocked.
- Air supply: keep storage, boxes, and insulation away from the burner and air inlet. Don’t store gasoline or other flammables near any water heater.
- CO alarms: under Section 553.885, homes built on or after July 1, 2008 with a fossil-fuel-burning appliance, a fireplace, or an attached garage must have a carbon monoxide alarm within 10 feet of each bedroom. Even in older homes, a CO alarm is a smart addition if you have gas.
Replacing a water heater: permits
In unincorporated Orange County, the county’s permit guide says that for a water heater replacement, “Yes, you need a plumbing permit and possibly an electrical permit.” Homeowners can pull permits only for their own primary residence, after an owner-builder verification. Otherwise a licensed contractor pulls the permit. Other counties and cities have similar requirements, so check yours. A permitted install gets inspected, which matters for insurance claims and when you sell. See Florida building permits.
- Signs it may be time: rusty hot water, water leaking from the tank itself rather than a fitting, rumbling or popping that flushing doesn’t fix, or not enough hot water.
- New federal standards: the U.S. Department of Energy adopted new efficiency standards for tank water heaters in 2024, with compliance required for units made on or after May 6, 2029. Under the rule, larger electric tank units are expected to use heat pump technology, while smaller ones can still use standard electric elements. Units already in homes aren’t affected, and federal rules can change, so check the current status when you shop.
Hurricanes, outages, and flooding
- Emergency water: FEMA notes that water from your home’s water heater tank is safe to drink if you can get to it. A full tank holds tens of gallons. Turn off the power or gas first, then draw water from the drain valve.
- Boil-water notices: if your utility issues one, close the main water valve if you want to keep the tank’s water uncontaminated.
- After flooding: if a gas or electric water heater sat in floodwater, don’t turn it back on until a qualified professional inspects it. Controls, burners, and elements are often ruined.
- Before refilling: after an outage or repair, make sure the tank is full before restoring power.
See the hurricane prep checklist and flood zones explained.
Yard and home rules series:
- Tree care and removal
- Fence rules
- Backyard rules: fires, fireworks, and noise
- Driveways
- Water heater maintenance (this article)
Frequently Asked Questions
Drain a gallon or two every six months and do a full flush once a year, following your owner’s manual. If your water is hard, flush more often.
The Consumer Product Safety Commission recommends 120°F. At 140°F, water can burn skin in six seconds.
Usually yes. In unincorporated Orange County, a replacement needs a plumbing permit and possibly an electrical permit. Homeowners can pull permits only for their own primary residence.
FEMA says water from your home’s water heater tank is safe to drink if you can access it. Turn off the power or gas first, and don’t turn the heater back on until the tank is full again.
Not for units already in homes. DOE’s 2024 standards apply to tank water heaters made on or after May 6, 2029. Larger electric tank units are expected to use heat pump technology, while smaller ones can still use standard elements. Check the current status when you shop, since federal rules can change.
Sources
- Consumer Product Safety Commission: Tap water scalds
- Village of Carpentersville Public Works: Water heater maintenance
- Florida Statutes, Section 553.885: Carbon monoxide alarms
- Orange County: Do I need a permit?
- FEMA: Emergency water sources
- U.S. Department of Energy: Consumer water heater standards
- Federal Register: Energy conservation standards for consumer water heaters (May 6, 2024)
This article is for general informational purposes only and isn’t financial, legal, insurance, or tax advice – for guidance specific to your situation, talk to a licensed professional.